Grading and Grade Point Averages (GPA)

note for Physical and Occupational Therapy : A grade of C+ is a minimum required passing grade for courses with the subject codes of OCC1, PHTH, and POTH. A grade of C is a minimum required passing grade for all other courses. For complete details, refer to the Rules and Regulations, available at A grade of C+ is a minimal needed pass grade for courses with the national codes of OCC1, PHTH, and POTH. A grade of C is a minimum command pass grade for all other courses. For complete details, refer to the Rules and Regulations, available at mcgill.ca/spot/programs Instructors may submit concluding grades as either letter grades or in percentages, but the official degree in each course, which displays on the transcript is the letter grade. Where allow, a class average appears on transcripts expressed as the letter grade most congressman of the classify performance. In such cases, the class average is calculated for courses, where the entire number of grades in all of its course sections is 25 or more, and the grades have a grade point ( e.g. grades of S, U or P don ’ t have grade points ) .
Since fall 2002, the University has only used letter grades on transcripts and verification forms.

Grades A through C represent satisfactory passes, D a conditional ( non-continuation ) communicate, and F a failure. certain courses have been approved for Pass/Fail ( P/F ) grade. Students may besides designate elective courses to be graded under the S/U option. See Courses Taken under the Satisfactory/Unsatisfactory ( S/U ) choice .
You must obtain a grade of C or better in courses that you take to fulfil program requirements. You may not register in a course unless you have passed all the prerequisite courses with a grade of C or better, except by written permission of the appropriate department moderate .

Grades Grade Points Numerical Scale of Grades
A

4.0

85 – 100%

A-

3.7

80 – 84%

B+

3.3

75 – 79%

B

3.0

70 – 74%

B-

2.7

65 – 69%

C+

2.3

60 – 64%

C

2.0

55 – 59%

D

1.0

50 – 54%

F (Fail)

0

0 – 49%

Note for Engineering:

The Faculty of Engineering does not use this numeral scale. See Note for Engineering below .

Note for Law:

Faculty of Law does not use this numeric scale .
The University assigns grade points to letter grades according to the table above. Your academic Standing ( e.g. satisfactory, probationary ), which is your academic status at the end of each term, is determined by a class point median ( GPA ), which is calculated by multiplying the course credit by the grade points, and dividing the union by the sum course GPA credits. The GPA consequence is truncated by two decimal fraction points and not rounded astir to the nearest decimal point. For model, a GPA of 3.596 will display on the transcript as 3.59 and is NOT rounded up to 3.60.

GPA credits are the credits of courses with grades that are assigned grad points .

The terminus grade point average ( TGPA ) is the GPA for a given term calculated using all the applicable courses at the like level in that term. The accumulative grade point modal ( CGPA ) is the GPA calculated using your stallion phonograph record of applicable courses at McGill at the like level ; if you change levels, for example, from undergraduate to graduate, the CGPA starts again .
This policy took consequence in January 2003. Prior to January 2003, if your degree plan had changed, e.g., from B.Sc. to B.A., the CGPA calculation restarted again. For students with academic data anterior to Fall 2002, who are registered in a unlike program or in a different level post-Fall 2002, the transcript displays a special message regarding the CGPA resume .
If you repeat courses, all concluding grades are included in the GPA calculation. therefore, grades of D or F continue to be used in the CGPA calculation evening after you repeat the course or if you take a supplementary interrogation. note that credits are only granted once for a recur course careless of the spend grad .
You must obtain a minimum CGPA of 2.00 to be considered for graduation with a McGill degree .
eminence :

During the first week of lectures, each instructor will provide you
with a written course outline. This information should include, where
appropriate:

  • whether there will be a
    final examination in the course;
  • how term work will affect
    the final grade in the course;
  • how term work will be
    distributed through the term;
  • whether there will be a
    supplemental examination in the course, and if so, whether the supplemental
    exam will be worth 100% of the supplemental grade, or whether term work will be
    included in the supplemental grade (courses with formal final examinations
    must have supplementals);
  • whether students with grades
    of D, F, J, or U will have the option of submitting additional work, and, if
    so, how the supplemental grade will be calculated with the extra work (applicable only to students in Science and B.A. & Sc.).

During the first week of lectures, each teacher will provide you with a written course delineate. This data should include, where allow : bill for mastermind : In the Faculty of Engineering, letter grades are assigned according to the grading scheme adopted by the professor in charge of a particular course. This may not correspond to grades indicated in the “Numerical Scale of Grades” column in Grading and Grade Point Averages. A
grade of
D indicates marginal performance which is
acceptable only for Complementary Studies
courses (i.e., Group A Impact of Technology on
Society and Group B Humanities and Social
Sciences, Management Studies and Law), Natural Science
Complementary Courses (for Computer Engineering and Software
Engineering students from CEGEP), and Elective Courses (for
Mechanical Engineering students from CEGEP and for Architecture students). A grade of D is not acceptable for required (core) courses (including Year 0 (Freshman) math and science courses), technical complementary courses, laboratory complementary courses, or courses in any other category of the Engineering programs. Individual departments/schools will decide if
a student with a D in a prerequisite course(s) may take the
subsequent course.

Grades have the following designations:
A, A- Very Good
B+, B, B- Good
C+, C Satisfactory
D Conditional Pass
F Fail

In the faculty of Engineering, letter grades are assigned according to the grading system adopted by the professor in charge of a particular course. This may not correspond to grades indicated in the “ Numerical Scale of Grades ” column in Grading and Grade Point Averages. A mark of D indicates borderline operation which is acceptable only for Complementary Studies courses ( i.e., Group A Impact of Technology on Society and Group B Humanities and Social Sciences, Management Studies and Law ), Natural Science Complementary Courses ( for Computer Engineering and Software Engineering students from CEGEP ), and elective course Courses ( for Mechanical Engineering students from CEGEP and for Architecture students ). A rate of D is not acceptable for required ( kernel ) courses ( including Year 0 ( Freshman ) mathematics and science courses ), technical complemental courses, lab complemental courses, or courses in any other class of the Engineering programs. Individual departments/schools will decide if a student with a D in a prerequisite course ( randomness ) may take the subsequent course.

spot_imgspot_img

Subscribe

Related articles

Biggest Social Media Platforms as Per User Base

The web is the sacred lifeline of industrial development...

AniMixPlay Review – Is AniMixPlay Safe?

AniMixPlay is a website where you can watch anime...

TweakVip and Offroad Outlaws

There are several applications that make your life more...

The Benefits of Green Buildings

The term green building can be used to describe...

Pacman 30th Anniversary: New Google Doodle

A modified version of the Google doodle honoring Pacman...